Page 8 of 11
UV point emitter system for connecting to an optic cable of maximum 8mm diameter (active core diameter).
Connection to multiple fibre cables is also possible.
A UV-C optimised system.
Cost-effective standard device for universal application.
Different UV spectra are possible (eg UV-A or UV-C) Cost-effective lamps or replacement emitters.
Simple time control or connection to SPS. more...
Heat seal applications Heat Sealing/ Heat seal application Flex (FPC) to glass (LCD) and Heat seal-/ Heat seal application circuit board (PCB) to flex (FPC) to glass(LCD) more...
Soldering of single stranded wires on a PCB.
Use of a profiled soldering bar for the optimal positioning of the stranded wires to the soldering pads and for an improved heat input compared to a flat soldering bar.
The profiling of the soldering bar is product-specific and, therefore, can be adapted to the respective wire cross section.
There is an open choice of the number of profilings. Profilings can be of different shapes and sizes.
Thus conductors with different cross sections can be soldered in just one process step. more...
Hot Bar Soldering System with sliding table (Desktop-Edition).
With exchangeable base plate on the sliding table for different jigs and workpiece holders. Dimensions of sliding table: 250x250mm.
The workpiece holder can be loaded in the extracted state of the sliding table. Standard: Manual movement of the sliding table.
Option: Automatic drive
The table is locked automatically and the Hot Bar Soldering process is initiated.
The system enclosure is available in different versions (e.g. ESD acryl glass or profile enclosure with safety door).
Semi-gimballed suspension of the soldering bar for best possible co-planar pressure of the soldering bar on the solder joint (for the soldering of plane solder joints).
Precise linear guide for stranded wire- or cable solderings. Adjustable pressure for both options.
Quick-change system for soldering bars with plug-in connector more...
Heat staking application for fixing a circuit board in a plastic body.
The circuit board is located in an injection moulding part with prepared parts.
The plastic domes fed through the circuit board are formed into a rivet by the die, so that the circuit board is fixed in the plastic part.
Thermoplastic materials such as PA, PP, PBT, POM, PC and PE (also with glass fibre content) are caulked. more...
Manual Dispensing Valve with one or two MV-2000.
Ideal e.g. for 2-component high-performance structural adhesives for no-mix method.
Both components are dispensed as one-on-the-other or adjacent beads onto the components to be joined.
During the process, both beads are crumpled together; the curing begins.
Component ratio: 100:100 parts by volume. more...
UV point emitter system which can be connected to up to 6 optic cables, each of 5m diameter (active core diameter).
Connection to multiple fibre cables is also possible.
The UV radiation produced by the point emitter is coupled into two optic cables (one at the front and one at the back of the instrument) Both cables can be controlled separately.
Irradiation is started by means of a foot switch and irradiation times can be programmed at each cable connection.
Optionally, sensors can be incorporated to monitor the aperture opening. UV-A filter caps are also optionally available. more...
Soldering of single stranded wires on a PCB.
Use of a profiled soldering bar for the optimal positioning of the stranded wires to the soldering pads and for an improved heat input compared to a flat soldering bar.
The profiling of the soldering bar is product-specific and, therefore, can be adapted to the respective wire cross section. There is an open choice of the number of profilings.
Profilings can be of different shapes and sizes. Thus conductors with different cross sections can be soldered in just one process step. more...
Heat staking application for fixing a circuit board in a plastic body.
The circuit board is located in an injection moulding part with prepared parts.
The plastic domes fed through the circuit board are formed into a rivet by the die, so that the circuit board is fixed in the plastic part.
Thermoplastic materials such as PA, PP, PBT, POM, PC and PE (also with glass fibre content) are caulked. more...
Heat seal-/ Heat seal application circuit board (PCB) to flex (FPC) to glass(LCD) more...
UV point emitter system which can be connected to up to 8 optic cables, each of 5m diameter (active core diameter).
Connection to multiple fibre cables is also possible.
The UV radiation produced by the point emitter is coupled into two optic cables (one at the front and one at the back of the instrument) Both cables can be controlled separately.
Irradiation is started by means of a foot switch and irradiation times can be programmed at each cable connection.
Optionally, sensors can be incorporated to monitor the aperture opening.
UV-A filter caps are also optionally available. more...
Soldering of single stranded wires on a foil structure (FPC).
Use of a profiled soldering bar for the optimal positioning of the stranded wires to the soldering pads and for an improved heat input compared to a flat soldering bar.
The profiling of the soldering bar is product-specific and, therefore, can be adapted to the respective wire cross section. There is an open choice of the number of profilings.
Profilings can be of different shapes and sizes. Thus conductors with different cross sections can be soldered in just one process step. more...
Small but yet very robust diaphragm dispensing valve.
Due to its simple design this valve is very easy to handle and simple to maintain.
The valve lift is adjustable, the membrane is Teflon coated. The through-flow body is made of polyethylene.
The through-flow hole has a diameter of -up to 2 mm. more...
Typical application with an octuple heat staking head. Linear arrangement of two heat staking dies, each with four forming elements.
Standard heat staking system with pneumatically driven turntable (330mm diameter), fitted with two component holders. During the time that the outside workpiece carriers are being unloaded and loaded, the product located in the system is sealed.
Temporarily heated system, where active cooling of the product takes place after the heating phase.
A Stand-alone system which can be operated from a standing or sitting operating position.
The HVS 40i is quoted by us as a âmodularâ system. Consequently, we can meet customer functional specifications from simple systems, which are purely thermally monitored, to completely process-monitored expansion sections with component raised- and lowered-distance measurement, permanent force measurement an more...
High intensity UV point emitter system for connecting to an optic cable of maximum 8mm diameter (active core diameter).
Connection to multiple fibre cables is also possible.
Cost-effective high power device (up to 20W/cm²) for universal application.
Simple time control or connection to SPS. more...
Soldering of a flex foil on a PCB.
Hot Bar Soldering with flat soldering bar.
The positioning of the flex foil on the soldering pads of the PCB is realised with alignment pins and corresponding drillings in flex and PCB. more...
Heat seal joints are carried out with so-called âanisotropically conductive adhesivesâ. In this way, for example, flexible foils are contacted with conductor paths (FPC) on circuit boards or the glass-connection face of an LCD or OLED module.
Anistropic adhesives are filled with electrically conductive particles. These particles are so small that an electrically conductive connection in the X- or pressure direction is created, while there is no contact in the Z-direction. On the application of heat (around 140ºC) and pressure (14-17 Kg/cm²), the adhesive begins to flow. When the adhesive cools under pressure, the conductive particles are âfrozenâ in position and retain their conductivity. The adhesive has a good mechanical strength after cooling.
Typical abbreviations for such adhesives are:
ACA â anisotropic conductive adhesive
ACF â anisotr more...
Typical application sprue removal. As a cost-effective alternative to laser cutting for can be used for the clean removal of sprue removal, temporarily heated knife-type tools can be used for the clean removal of casting sprue.
Cutting edges are clean without chips and without any âdrawing of plastic fibresâ and there are no residual particles on the product to be removed.
Standard heat staking system has a manually operated sliding table (300x300mm working plate).
There is automatic halting of the table when it reaches the working position and the table is releasedafter a fault-free process or after authorized acknowledgement of malfunction.
It can be fitted with workpiece holders.
Temporarily heated system, where active cooling of the product takes place after the heating phase.
A Stand-alone system which can be operated from a standing or sitting operati more...
Typical application with a triple heat staking head. Circular arrangement of the individual heat staking dies.
Standard heat staking system with pneumatically driven turntable (330mm diameter), fitted with two component holders. During the time that the outside workpiece carriers are being unloaded and loaded, the product located in the system is sealed.
Temporarily heated system, where active cooling of the product takes place after the heating phase.
A Stand-alone system which can be operated from a standing or sitting operating position.
The HVS 40i is quoted by us as a âmodularâ system. Consequently, we can meet customer functional specifications from simple systems, which are purely thermally monitored, to completely process-monitored expansion sections with component raised- and lowered-distance measurement, permanent force measurement and data communication.
more...
Heat staking system for retrofitting into a customer rack.
If required, we can retrofit the heat staking components into a ready-made customer rack. The required components such as the multiple heat staking head, control cabinet and operator control panel are fitted into the housing to meet customer requirements, integrated into the rack and then tested.
In this example, a circuit board with a 6x heat staking heads is fixed in the plastic housing.
Temporarily heated system, where active cooling of the product takes place after the heating phase.
Custom-built systems and special machines are designed, manufactured, tested and commissioned for operation in our factory. We carry out all the manufacturing stages required for the heat staking process.
We can meet customer functional specifications from simple systems, which are purely thermally monitored, to completely proce more...
Deutsch
English
Standard-Systems
