Page 10 of 11
Soldering of single stranded wires on a PCB.
Use of a profiled soldering bar for the optimal positioning of the stranded wires to the soldering pads and for an improved heat input compared to a flat soldering bar.
The profiling of the soldering bar is product-specific and, therefore, can be adapted to the respective wire cross section.
There is an open choice of the number of profilings. Profilings can be of different shapes and sizes.
Thus conductors with different cross sections can be soldered in just one process step. more...
Soldering of single stranded wires on a PCB.
Use of a profiled soldering bar for the optimal positioning of the stranded wires to the soldering pads and for an improved heat input compared to a flat soldering bar.
The profiling of the soldering bar is product-specific and, therefore, can be adapted to the respective wire cross section.
There is an open choice of the number of profilings. Profilings can be of different shapes and sizes.
Thus conductors with different cross sections can be soldered in just one process step. more...
Soldering of an OLED on a PCB.
Hot Bar Soldering with flat soldering bar.
The positioning of the flex foil on the soldering pads of the PCB is realised with alignment pins and corresponding drillings in flex and PCB. more...
Heat seal applications Heat Sealing/ Heat seal application Flex (FPC) to glass (LCD) and Heat seal-/ Heat seal application circuit board (PCB) to flex (FPC) to glass(LCD) more...
Hot Bar Soldering System with automatic rotary table (Desktop-edition).
Diameter of turntable: 330mm.
On the turntable of the system there are mounting possibilities for 2 product jigs.
Simultanous loading / unloading and soldering.
The turntable is actuated by a drive wheel, launched by a two-handed release.
The turntable is locked automatically and the Hot Bar Soldering process is initiated.
The system enclosure is available in different versions (e.g. ESD acryl glass or profile enclosure with safety door).
Semi-gimballed suspension of the soldering bar for best possible co-planar pressure of the soldering bar on the solder joint (for the soldering of plane solder joints).
Precise linear guide for stranded wire- or cable solderings. Adjustable pressure for both options.
Quick-change system for soldering bars with plug-in connector and mounting device on a p more...
Hot Bar Soldering System with automatic rotary table Desktop-edition.
Diameter of turntable: 330mm.
On the turntable of the system there are mounting possibilities for 2 product jigs.
Simultanous loading / unloading and soldering.
The turntable is actuated by a drive wheel, launched by a two-handed release.
The turntable is locked automatically and the Hot Bar Soldering process is initiated.
The system enclosure is available in different versions (e.g. ESD acryl glass or profile enclosure with safety door).
Semi-gimballed suspension of the soldering bar for best possible co-planar pressure of the soldering bar on the solder joint (for the soldering of plane solder joints).
Precise linear guide for stranded wire- or cable solderings. Adjustable pressure for both options.
Quick-change system for soldering bars with plug-in connector and mounting device on a pne more...
Heating rail unit and semi-gimballed compensation element.
A complete, product-specific heat sealing head.
Connection to the system via a plug-in connector simplifies maintenance and reduces possible downtime.
The integral semi-gimballed suspension is a compensation mechanism to create a uniform co-planar pressure of the heater rail on the sealing face.
Known imbalances of the product are automatically compensated. more...
Heating rails for heat sealing systems are supplied in infinitely variable lengths from 5mm to 300mm.
Contact units, which are gold-plated on the edges are fitted to an aluminium base and these provide electrical contacts for the measurement wires of the control electronics and the heater connection wires.
The actual heater elements, the so-called heater strips, are thermally insulated from the base and fixed to the contact units by a âbelt tensioning systemâ.
The heater strips have a low thermal mass, so that they are heated and cooled in the shortest possible time.
At several points on the inside of the heating strips there are additional temperature sensors for collective temperature monitoring.
The heater rails are extremely robust and durable. Replacement, e.g. at product change-over, is achieved with few handgrips.
In complex production plants, the h more...
Large area Heat Seal System.
A system for large area heat sealing- and lamination processes up to 200x200mm.
Temperature range 50-300ºC, application force up to 15,000N.
A large surface heating head with multiple temperature monitoring and optimum thermal homogeneity at the heating head.
The transfer table system is equipped with a customised workpiece carrier.
To absorb the high forces necessary in the process, the transfer table is fitted with a high load linear guide.
There is integrated precision temperature control, timing control and protection and monitoring. more...
Industrial Dispensing Pinch Valve designed for automated dispensing of low and medium viscous fluids.
Hence 2K materials and abrasive liquids can be dispensed. more...
Product jig for the positioning of a ribbon cable on a PCB.
The cable is held in position by vacuum.
Fine adjustment of the conductor paths of the cable on the soldering pads of the PCB by means of an adjusting screw. more...
Detailed information: Positioning of stranded wires on the soldering areas of the PCBs.
The wires are guided in grooves and are held in position by a clamping device.
A "comb" made of sheet metal ensures the correct position of the wires.
The insulation of the stranded wires is stopped by the comb.
Just the stripped and pre-tinned part of the wires is allowed to touch the soldering pads.
The removal of the finished parts is facilitated by an ejector mechanism. more...
A UV-F 400, 450W large surface emitter in a large lightbox with a manually operated shutter.
The door of the box can be opened only when the shutter is closed preventing radiation from entering the chamber.
When the shutter is open, the door is locked.
No mains supply voltage is necessary for the lightbox and the UV emitter has a separate power supply.
Adaptor plates are available to fix different UV emitters, such as hand lamps, UV-F 400 or specific customer instruments. more...
Basic Dispensing Pressure Control for different dispensing valves. more...
Product jig for the soldering of single stranded wires on a PCB. more...
Double tank system with two 6bar pressure vessels.
Ideal for dispensing of 2-component materials, which are dosed in the 50/50 ratio with a static mixing nozzle.
The pressure vessels are each designed to accommodate containers up to half a liter.
The necessary pressure of each pressure vessel can be separately set.
An integrated timer controls the pulse duration of the attached dispensing valve. Optional fill level sensors and tank pressure sensors can be integrated.
Different dispensing valves can be controlled by the tank system. more...
Very robust diaphragm dispensing valve.
Due to its simple design this valve is very easy to handle and simple to maintain.
The membrane is Teflon coated. The through-flow body is made of stainless steel.
The through-flow body can be equipped with a heating or a temperature control.
The temperature control is designed for a temperature range of + /-20K or can be adapted to customer requirements.
The valve lift is adjustable and can optionally be monitored by a sensor (dispensing control). more...
Manual Dispensing Valve with dispensing control.
Ideal e.g. for 2-component high-performance structural adhesives for no-mix method.
Both components are dispensed as one-on-the-other or adjacent beads onto the components to be joined.
During the fitting process, both beads are crumpled together; the curing begins.
Component ratio: 100:100 parts by volume. more...
Product jig for the positioning of an LCD with connection flex on a PCB.
Flex is held in position by means of a simple clamp lever. more...
Double product jig for the soldering of ribbon cables on PCBs.
The cables are fixed and held in position by a clamping device.
The positions of the PCBs can each be adjusted by an adjusting mechanism. more...
Deutsch
English
Standard-Systems
